1Tiles
Six small tiles around the legend, filled from the top, clockwise. A hike is a route file (GPX, KML or GeoJSON; pick several at once for several tiles); favourite places is a map with red dots; a photo is your own picture in a press-in frame, with a 10 × 15 cm print file. You can also drop files here. Everything stays on your computer.
2Fit of the selected map tile
Each map tile is fitted automatically. Click one in the list or on the map to fine-tune it.
3Legend
The centre tile: the north mark, a big headline, and lines above and below it. The lines fill in from the trip (if one is loaded in Trip tile mode) and the hikes; edit them freely, or click Auto to go back. Each tile also gets a diamond in the tray corner clockwise of it, with its name and details.
1Route
GPX, KML, GeoJSON or Polarsteps locations.json (from Polarsteps' "copy of my data" export, one folder per trip). The file is read locally and never uploaded.
2Tile layout
Pick a layout. The scale shows how many km 10 cm on the tile covers (lower = more detail). Click hexagons on the map to add or remove tiles.
Turns the whole map on the tiles, so more of the land you want fits in (the tiles themselves stay where they are). The north mark on the border turns with it. Saved per trip.
3Label
Format: NAME · YEAR, e.g. LOFOTEN · 2026. Engraved in a plaque that sits on the border of the bottom tile, followed by a small north mark (▲N).
+Hikes on this trip
Marks where the trip's day hikes started: the hike's name engraved on a small plate next to its starting point, clear of the route and the water. Hikes that start at the same place share a plate, one name per line.
+Hike cluster on the wall
Shows the hike cluster (made in Hike cluster mode) next to the trip, so you see both in one view and choose where it hangs. One border runs around the trip and the cluster together: there is no border where they meet.
4Terrain
Fetches free elevation data (Terrain Tiles on AWS Open Data) for the area of the tiles. Only map tiles are requested; your route is not sent anywhere.
From OpenStreetMap, so only for areas up to 60 km across. The main river (and others that run a long way over the tiles) is either a filament line, a groove for a 1.75 mm blue strand sunk 0.4 mm into the valley (where the route crosses, the grooves run into each other and the red goes on top; where the river runs right beside the route, it is moved out so a wall of land stays between the two grooves; a river that stops just short of a lake is run on into it), or a blue water insert at least 2.5 mm wide whose top follows the valley down. Each river is one or the other along its whole length; switch per river below. Smaller rivers and streams are left out.
Hikes and other small areas (up to 60 km across) take their coastline and lakes from OpenStreetMap, so small lakes and fjords come out right. Big trips use the elevation data for the sea and Natural Earth's 1:10 million map for lakes.
Lakes, bays and other water smaller than this become land, so there are fewer tiny pieces to glue. Orange on the map = water that turns into land. Saved per trip in the settings file.
Islands smaller than this (specks of land in a lake or the sea) become water, as they would never print; purple on the map. Islands the route runs on are always kept. 0 keeps every island. Saved per trip.
How far the highest point stands above the lowest land (or the sea). Auto gives 14 mm for trips with 1,500 m or more of height difference and less for flatter trips. Saved per trip.
Set for the hike with the most height difference; the others scale with theirs, so a flat walk stays flatter than a mountain hike. Auto is 70 % of what a big tile would get.
For rugged terrain: the route gets a smooth surface at the height of the land around it, with a level strip and then a slope back to the terrain on each side (this wide in all), so the red stays visible between tall peaks. Smaller keeps more detail. Off: the land is left as it is and the groove floor is just smooth. On or off per tile:
5Generate and download
Each tile comes as a land model (print in your base colour) and a water model (print in blue) that glues into the pockets. A border runs along the outer edge of the whole trip (and of its hike cluster, when it hangs next to it).
Each hike tile comes as land + water insert, plus the legend tile, a plain filler for each empty slot, and the 200 mm tray they sit in. Download them one by one, as print plates, or everything in one zip.
How tightly the parts fit depends on your printer and filament, not on the series, so these settings don't change the look. Print the fit test plate once per printer and filament: it has every part that needs a fit, each with labelled variants around your current values. Type in the ones that fit best.
Off: the water tops are flat and clean. On: a gentle 0.3 mm swell; the slicer turns it into a few soft, irregular contour rings, like ripples.
The spacing of the mesh points over the terrain. Finer shows more of the landscape; below a 0.4 mm nozzle's line width there is little more to gain. Saved per trip.
Series constants (only change for a v2)
Changing anything here breaks consistency with existing tiles. The badge at the top then shows "custom".